D-MAX DMC-20SEC Manual de usuario descargar pdf (Pagina 3)

3

11 May, 2006 DMC-A2 Series (ALD-00029)

Macro Sensors Tel. (856) 662-8000

www.macrosensors.com

Prog.

SP1 SP2 SP4SP3 SP5 SP6

P

4 Secs

[_ _ _INPUT

SETUP]

Prog.

SP1 SP2 SP4SP3 SP5 SP6

P

[_ _ _SELECT

SUPPLY

FREQUENCY]

Prog.

SP1 SP2 SP4SP3 SP5 SP6

Prog.

SP1 SP2 SP4SP3 SP5 SP6

YES

YES

START

Prog.

SP1 SP2 SP4SP3 SP5 SP6

P

See Page 4 for further details

YES

YES

P

Or press the P button 4 times to

EXIT (bypassing the remaining modes)

and return to the Operational Display

Input Setup

Select the required setting

to suit the power supply

frequency. If the mains

supply is 50 Hz, then

select 50 Hz to reject

50 Hz noise. Correspondingly,

if the mains supply is 60 Hz,

then select 60 Hz to reject

60 Hz noise.

P

[_ _ _SELECT

EXCITATION

IN KHZ]

OR

Prog.

SP1 SP2 SP4SP3 SP5 SP6

[ 11.52]

[ 1.92]

[ 2.88]

[ 3.84]

[ 5.76]

[ 7.68]

[ 9.60]

P

[_ _ _SELECT

OUTPUT RATE]

Prog.

SP1 SP2 SP4SP3 SP5 SP6

1 Hz = 1/sec

4 Hz = 4/sec

10 Hz = 10/sec

20 Hz = 20/sec

[_ _ _SELECT

EXCITATION

IN KHZ]

Prog.

SP1 SP2 SP4SP3 SP5 SP6

[ 1.6]

[ 2.4]

[ 3.2]

[ 4.8]

[ 6.4]

[ 8.0]

[ 9.6]

P

60 Hz Selection

50 Hz Selection

P

[_ _ _SELECT DECIMAL POINT CH1]

Prog.

SP1 SP2 SP4SP3 SP5 SP6

Select the decimal point position

for the required resolution for CH1:

¥ 0.1 - Tens.

¥ 0.12 - Hundreds.

¥ 0.123 - Thousands.

¥ 0.1234 - Ten thousands.

¥ 0.12345 - Hundred thousands.

Prog.

SP1 SP2 SP4SP3 SP5 SP6

Prog.

SP1 SP2 SP4SP3 SP5 SP6

Prog.

SP1 SP2 SP4SP3 SP5 SP6

OR

OR

YES

YES

P

[_ _ _SELECT DECIMAL POINT CH2]

Select the decimal point position

for the required resolution for CH2:

¥ 0.1 - Tens.

¥ 0.12 - Hundreds.

¥ 0.123 - Thousands.

¥ 0.1234 - Ten thousands.

¥ 0.12345 - Hundred thousands.

Calibration

[_ _ _SELECT

CALIBRATION

CHANNEL]

[ 0.1]

[ 0.12]

[ 0.123]

[ 0.1234]

[0.12345]

Prog.

SP1 SP2 SP4SP3 SP5 SP6

[ 0.1]

[ 0.12]

[ 0.123]

[ 0.1234]

[0.12345]

Select sensor excitation

frequency according to

sensor specification to

optimize performance.

Press the button to enter the Calibration Mode

Input Setup

The input setup mode allows you to configure five input setup settings in linked menus.

1 2 3 4 5 6 7 8 ... 27 28

Comentarios a estos manuales

Sin comentarios