D-MAX DMC-20SEC Manual de usuario descargar pdf (Pagina 11)

11

11 May, 2006 DMC-A2 Series (ALD-00029)

Macro Sensors Tel. (856) 662-8000

www.macrosensors.com

Installation

96 mm

(3.78")

48 mm

(1.89")

3.9 mm

(0.15") typical

FRONT VIEW

1/8 DIN 96x48mm

The 96x48 mm case is

particularly suitable for

mounting in mosaic panels

or insulative panels up to 2"

thick. They can also stack

mount, 2 up in existing

cutouts for 1/4 DIN (96x96

mm) or 4 up in 1/2 DIN

(96X192 mm).

40.8 mm

(1.61")

117 mm

(4.61")

SIDE VIEW

5.3 mm

(0.21")

3.7 mm

(0.15")

43.4 mm

(1.71")

DIN Cutout spacers

Straight-thru Connector for

meters with output board

20 mm (0.79")

Right-angled Connector

11.8 mm (0.47")

PANEL CUTOUT

Case will mount in standard 1/8 DIN coutouts

45 mm

(1.77")

Snug Fitting

Mosaic Fitting

92 mm

(3.62")

Loose Fitting

91.6 mm

(3.6")

40.8 mm

(1.61")

8 places

3 12")

8 places

4 mm

(0.16")

43.4 mm

(1.71")

1/8 DIN

Cutout spacers

87.4 mm

(3.45")

Panel adaptor plates are

available to retrofit most

existing panel cutouts.

For additional strength, extra Mounting

Slide Clips can be ordered and doubled up

one behind the other. P/N: (75-DMTCLIPF)

TOP VIEW

87.4 mm

(3.45")

mosaic

fitting

95.4 mm

(3.77")

Max. panel thickness

50mm

(1.97")

96 mm

(3.78")

91.6 mm

(3.6")

DIN

Cutout

Spacer

To open rear cover,

use a small flat

blade screw driver.

Press down lightly to

release catch on top

or bottom of case

and lever outwards.

4.7 mm

(0.19")

DIN Cutout Spacer

2 mm

(0.08")

Connector

Socket

Prog.

SP1SP1

SP1 SP2 SP4SP3 SP5 SP6

Prog.

SP1SP1

SP1 SP2 SP4SP3 SP5 SP6

Prog.

SP1 SP2 SP4SP3 SP5 SP6

STEP A Prepare the Panel

1) Cut a hole in the panel to suit the panel

cutout. See panel cutout sizes above.

STEP B Install the Meter

1) Remove both mounting clips from the meter.

2) Push the meter into the panel cutout from the

front of the panel.

3) Attach both mounting clips to the meter from

the rear of the panel and push them towards

the front of the panel until the meter is firmly

held.

STEP C Connect the Cables

1) Connect all input and output signal cables to the

connector pins (See

Connector Pinouts

for details).

2) Connect the power cables to the connector pins

(See

Connector Pinouts

for details).

WARNING

AC and DC power supply voltages

are hazardous. Make sure the

power supply is isolated before

connecting to the meter.

1

2

3

Installation Procedure

1

2

3

Figure 4 – DMC-A2 Series Installation Sequence

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 27 28

Comentarios a estos manuales

Sin comentarios