D-MAX DSC-300Si5 Manual de usuario

USER MANUAL DSC-300Si5/Se5 HIGH SPEED DOME CAMERA

8 Have you connect the power cable in the right direction ? If yes ① RED led, in the niddle of the connector, is lighted ② Use AC24V power sou

9 2-3. Connection diagram Reference to the following page. Connect the image line of a monitor User

10 Must use AC24V power source, current intensity must be less than 1.5A and must use a double winding trans

11 1). DIP SWITCH SETTING 3. DIRECIONS FOR USE Set the power of the camera switch-off to control

12 2) HOW TO SET PROTOCOL ① Please the power off ② Switch protocol that user wants to change on as above the cable

13 3) SETTING ADDRESS OF DIP SWITCHES. Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program. RX NO DIP SWITCH (HEX) RX

14 4) HOW TO USE OSD MENU 4-1. How to control OSD menu ● OSD (ON SCREEN DISPLAY) CONTROL It is the function to call up the Menu ＊User can not only s

15 4-2. Functional Descriptions of each Menu. 1. ID SET. It is the function to set ID of the camera. Move to No.1 menu and the screen moves as fol

16 4. SHUTTER SPEED Shutter speed is the duration of the electronic shutter. Set shutter speed to operate automatically (Auto) or manually (Nume

17 9. ZOOM MAX LIMIT Zoom max limit allows the user to define a limitation on the amount of telephoto zoom. The default setting is X46. Camera with

2

18 according to low light condition with medium sensing. ●AUTO-LOW: Convert to monochrome mode automatically according to low light condition with

19 F/F key, then it is moved to the previous screen automatically from the menu. • [SAVE]: Previous screen. [DELETE]: Remove. [ESC]: Cancel ＊Repe

20 ⑥ Run Function: Operate one of SWING/ ＊Set / Stop the function by a control keyboard GROU

21 You can look at how to set TRACE at “18. TRACE SET PAGE” ⑦ RETURN MENU PAGE: Move to a higher menu page if select this me

22 How to set TRACE Move to [SET] after pressing „ F/N KEY ‟ F/F KEY Check – Control the scenes that you want to save a joystick after the messa

23 17. ALARM PRESET SET PAGE The camera moves to a preset point automatically when Alarm activates in each ALARM CHANNEL. Set preset point

24 20. MOTION DETECTION SET Detect Level: 00 ~ 05 (High number is high sensing) Detect Position: 01 ~ 08 (Set up to 8 zones) (To set this function,

25 ③ Confirm, Next page ④ Fix the black square on the middle of area that you want to hide by a joystick, then go

26 << CAMERA SETUP p4 >> 22. Auto Tilt Mode : OFF 23. Smart Pan/tilt : On 24. Manual P/T Speed : Medium 25. Language: English

27 4-3. Functional Setting, Operating/Deletion by the Keyboard 1. Preset setting You can set Preset point up to 250. ① Preset Input. Preset

1 1. CAUTION -------------------------------------------------------------------------------- 2 2. INTRODUCTION OF PRODUCT 4 1). DESCRIPTION AN

28 ② Operation of Swing ③ End of Swing (Run Pan) (Run Tilt) 3. Group setting ① Start

29 EX). Register Group No. 1,3,6 as Tour ② Start / End Tour

30 4-4. OSD MESSAGE DISCRIPTION 1. PRESET MESSAGE CAM-001 GP:01 P002,T001,S64 CAM-001 Save Group 01 CA

31 CAM-001 SET TOUR GP:01 CAM-001 TOUR&GP:01 PRESET:001 CAM-001 CLEAR TOUR & GRP CAM-001

32 1. You must turn off the power switch before installation of this equipment 2. Avoid installation places where it is the ultimate cold, hot, and

33 exactly presser position or different. mode? preset in the set mode. When it activate alarm state, there is no sign on the keyboard controller Did

34 5. DIMENSION Wall mount bracket Ceiling mount bracket

35 In-ceiling mount bracket

36

37 8 7 9 6 1 2 5 4 3 17.2 Assembly of outdoor dome with pole mount pendant DS

2 Thank you for purchasing our product. Please operate the product after being fully aware of the manual. Pease contact us if you have any queri

38 Sub keyboard Sub keyboard

39 Set one main keyboard

40 MODEL INDOOR Signal system NTSC PAL Image sensor 1/4” Sony Ex-View CCD Effective pixels 768(H) X 494(V), 752(H) X 582(V), Horizontal resoluti

MODEL OUTDOOR Signal system NTSC PAL Image sensor 1/4” Sony Ex-View CCD Effective pixels 768(H) X 494(V), 752(H) X 582(V), Horizontal resoluti

3 Caution in Use Do not disassemble the unit and put alien substances in the unit. - Disassembling the unit or putting alien substances such as a me

4 1) DESCRIPTION AND FEATURES This camera has been designed elegantly for buildings, department stores that need to be in harmony with the inter

5 2) INSTALLATION AND CONNECTION 2-1. Name and function of each part INDOOR TYPE OUTDOOR TYPE Upper cover The

6 2-2. Installation INDOOR TYPE OUTDOOR TYPE Loosen the bolt of the back of lower cover by a screwdriver(+), then turn the c

7 Pull the cover up with grabbing the bottom of the camera after loosening the three bolts Open the connector cover, t